Sata Slot Adalah

Sata Slot Adalah

Advanced Host Controller Interface

Advanced Host Controller Interface (AHCI) is an open host controller interface published and used by Intel, which has become a de facto standard. It allows the use of advanced features of SATA such as hotplug and native command queuing (NCQ). If AHCI is not enabled by the motherboard and chipset, SATA controllers typically operate in "IDE[b] emulation" mode, which does not allow access to device features not supported by the ATA (also called IDE) standard.

Windows device drivers that are labeled as SATA are often running in IDE emulation mode unless they explicitly state that they are AHCI mode, in RAID mode, or a mode provided by a proprietary driver and command set that allowed access to SATA's advanced features before AHCI became popular. Modern versions of Microsoft Windows, Mac OS X, FreeBSD, Linux with version 2.6.19 onward,[13] as well as Solaris and OpenSolaris, include support for AHCI, but earlier operating systems such as Windows XP do not. Even in those instances, a proprietary driver may have been created for a specific chipset, such as Intel's.[14]

SATA revisions are typically designated with a dash followed by Roman numerals, e.g. "SATA-III",[15] to avoid confusion with the speed, which is always displayed in Arabic numerals, e.g. "SATA 6 Gbit/s". The speeds given are the raw interface rate in Gbit/s including line code overhead, and the usable data rate in MB/s without overhead.

SATA revision 3.0 (6 Gbit/s, 600 MB/s, Serial ATA-600)

Serial ATA International Organization (SATA-IO) presented the draft specification of SATA 6 Gbit/s physical layer in July 2008,[22] and ratified its physical layer specification on August 18, 2008.[23] The full 3.0 standard was released on May 27, 2009.[24]

Third-generation SATA interfaces run with a native transfer rate of 6.0 Gbit/s; taking 8b/10b encoding into account, the maximum uncoded transfer rate is 4.8 Gbit/s (600 MB/s). The theoretical burst throughput of SATA 6.0 Gbit/s is double that of SATA revision 2.0. It is backward compatible with earlier SATA implementations.[22]

The SATA 3.0 specification contains the following changes:

In general, the enhancements are aimed at improving quality of service for video streaming and high-priority interrupts. In addition, the standard continues to support distances up to one meter. The newer speeds may require higher power consumption for supporting chips, though improved process technologies and power management techniques may mitigate this. The later specification can use existing SATA cables and connectors, though it was reported in 2008 that some OEMs were expected to upgrade host connectors for the higher speeds.[25]

Released in July 2011, SATA revision 3.1 introduced or changed the following features:[26][27]

Released in August 2013, SATA revision 3.2 introduced the following features:[32]

Released in February 2016, SATA revision 3.3 introduced the following features:[41][42]

The new Power Disable feature (similar to the SAS Power Disable feature) uses Pin 3 of the SATA power connector. Some legacy power supplies that provide 3.3 V power on Pin 3 would force drives with Power Disable feature to get stuck in a hard reset condition preventing them from spinning up. The problem can usually be eliminated by using a simple “Molex to SATA” power adaptor to supply power to these drives.[44]

Released in June 2018, SATA revision 3.4 introduced the following features that enable monitoring of device conditions and execution of housekeeping tasks, both with minimal impact on performance:[45]

Released in July 2020, SATA revision 3.5 introduces features that enable increased performance benefits and promote greater integration of SATA devices and products with other industry I/O standards:[46]

SATA revision 3.5a was released in March 2021.

SATA revision 2.0 (3 Gbit/s, 300 MB/s, Serial ATA-300)

SATA revision 2.0 was released in April 2004, introducing Native Command Queuing (NCQ). It is backward compatible with SATA 1.5 Gbit/s.[18]

Second-generation SATA interfaces run with a native transfer rate of 3.0 Gbit/s that, when accounted for the 8b/10b encoding scheme, equals to the maximum uncoded transfer rate of 2.4 Gbit/s (300 MB/s). The theoretical burst throughput of the SATA revision 2.0, which is also known as the SATA 3 Gbit/s, doubles the throughput of SATA revision 1.0.

All SATA data cables meeting the SATA spec are rated for 3.0 Gbit/s and handle modern mechanical drives without any loss of sustained and burst data transfer performance. However, high-performance flash-based drives can exceed the SATA 3 Gbit/s transfer rate; this is addressed with the SATA 6 Gbit/s interoperability standard.

Announced in August 2005, SATA revision 2.5 consolidated the specification to a single document.[19][20]

Announced in February 2007, SATA revision 2.6 introduced the following features:[21]

SATA 1.5 Gbit/s and SATA 6 Gbit/s

SATA 1.5 Gbit/s and SATA 6 Gbit/s are compatible with each other. Most devices that are only SATA 1.5 Gbit/s can connect with devices that are SATA 6 Gbit/s, and vice versa, though SATA 1.5 Gbit/s devices only connect with SATA 6 Gbit/s devices at the slower 1.5 Gbit/s speed.

SATA revision 1.0 (1.5 Gbit/s, 150 MB/s, Serial ATA-150)

Revision 1.0a[2] was released on January 7, 2003. First-generation SATA interfaces, now known as SATA 1.5 Gbit/s, communicate at a rate of 1.5 Gbit/s, and do not support Native Command Queuing (NCQ). Taking 8b/10b encoding overhead into account, they have an actual uncoded transfer rate of 1.2 Gbit/s (150 MB/s). The theoretical burst throughput of SATA 1.5 Gbit/s is similar to that of PATA/133, but newer SATA devices offer enhancements such as NCQ, which improve performance in a multitasking environment.

During the initial period after SATA 1.5 Gbit/s finalization, adapter and drive manufacturers used a "bridge chip" to convert existing PATA designs for use with the SATA interface. Bridged drives have a SATA connector, may include either or both kinds of power connectors, and, in general, perform identically to their native-SATA equivalents.[16]

As of April 2010[update], the fastest 10,000 rpm SATA hard disk drives could transfer data at maximum (not average) rates of up to 157 MB/s,[17] which is beyond the capabilities of the older PATA/133 specification and also exceeds the capabilities of SATA 1.5 Gbit/s.

Kami mohon maaf atas kebingungannya, tetapi kami tidak bisa tahu apakah Anda adalah seseorang atau skrip.

Centang kotak ini dan kami akan berhenti menghalangi Anda.

Komponen Motherboard Berbicara mengenai hardware (perangkat keras), pada sistem komputer pasti akan berkaitan dengan CPU. Dalam komponen CPU terdapat yang namanya “Motherboard” atau “papaninduk”. Motherboard merupakan hardware yang fungsinya sebagai tempat dari berbagai jenis sistem komputer yang saling terhubung. Bisa dibilang, motherboard adalah media untuk menghubungkan perangkat komputer. Bentuk dari motherboard mirip papan seperti nama istilahnya. Membahas mengenai motherboard, ternyata hardware yang satu ini punya beberapa komponen-komponen yang mungkin belum banyak diketahui oleh orang banyak. Komponen-komponen ini tentunya mempunyai fungsi masing-masing. Yuk, simak pembahasannya! Komponen-Komponen Motherboard Berikut ini adalah komponen-komponen dari motherboard yang bisa Anda kenali serta dipelajari fungsinya agar tidak salah dalam memasang atau menggunakannya. 1.Socket Prosessor atau CPU Socket Ilustrasi Socket Prosessor CPU Socket adalah suatu komponen dari motherboard yang digunakan sebagai tempat untuk memasang prosesor. Dari tampilannya pada CPU, komponen yang satu ini memiliki 4 lubang yang berguna untuk penyangga dari Heatsink ...

Computer bus interface for storage devices

SATA (Serial AT Attachment)[a][2] is a computer bus interface that connects host bus adapters to mass storage devices such as hard disk drives, optical drives, and solid-state drives. Serial ATA succeeded the earlier Parallel ATA (PATA) standard to become the predominant interface for storage devices.

Serial ATA industry compatibility specifications originate from the Serial ATA International Organization (SATA-IO) which are then released by the INCITS Technical Committee T13, AT Attachment (INCITS T13).[3]

SATA was announced in 2000[4][5] in order to provide several advantages over the earlier PATA interface such as reduced cable size and cost (seven conductors instead of 40 or 80), native hot swapping, faster data transfer through higher signaling rates, and more efficient transfer through an (optional) I/O queuing protocol. Revision 1.0 of the specification was released in January 2003.[2]

Serial ATA industry compatibility specifications originate from the Serial ATA International Organization (SATA-IO). The SATA-IO group collaboratively creates, reviews, ratifies, and publishes the interoperability specifications, the test cases and plugfests. As with many other industry compatibility standards, the SATA content ownership is transferred to other industry bodies: primarily INCITS T13[3] and an INCITS T10 subcommittee (SCSI), a subgroup of T10 responsible for Serial Attached SCSI (SAS). The remainder of this article strives to use the SATA-IO terminology and specifications.

Before SATA's introduction in 2000, PATA was simply known as ATA. The "AT Attachment" (ATA) name originated after the 1984 release of the IBM Personal Computer AT, more commonly known as the IBM AT.[6] The IBM AT's controller interface became a de facto industry interface for the inclusion of hard disks. "AT" was IBM's abbreviation for "Advanced Technology"; thus, many companies and organizations indicate SATA is an abbreviation of "Serial Advanced Technology Attachment". However, the ATA specifications simply use the name "AT Attachment", to avoid possible trademark issues with IBM.[7]

SATA host adapters and devices communicate via a high-speed serial cable over two pairs of conductors. In contrast, parallel ATA (the redesignation for the legacy ATA specifications) uses a 16-bit wide data bus with many additional support and control signals, all operating at a much lower frequency. To ensure backward compatibility with legacy ATA software and applications, SATA uses the same basic ATA and ATAPI command sets as legacy ATA devices.

The world's first SATA hard disk drive is the Seagate Barracuda SATA V, which was released in Jan 2003.[8]

SATA has replaced parallel ATA in consumer desktop and laptop computers; SATA's market share in the desktop PC market was 99% in 2008.[9] PATA has mostly been replaced by SATA for any use; with PATA in declining use in industrial and embedded applications that use CompactFlash (CF) storage, which was designed around the legacy PATA standard. A 2008 standard, CFast, to replace CompactFlash is based on SATA.[10][11]

The Serial ATA spec requires SATA devices be capable of hot plugging; that is, devices that meet the specification are capable of insertion or removal of a device into or from a backplane connector (combined signal and power) that has power on. After insertion, the device initializes and then operates normally. Depending upon the operating system, the host may also initialize, resulting in a hot swap. The powered host and device do not need to be in an idle state for safe insertion and removal, although unwritten data may be lost when power is removed.

Unlike PATA, both SATA and eSATA support hot plugging by design. However, this feature requires proper support at the host, device (drive), and operating-system levels. In general, SATA devices fulfill the device-side hot-plugging requirements, and most SATA host adapters support this function.[1]

For eSATA, hot plugging is supported in AHCI mode only. IDE mode does not support hot plugging.[12]

SATA Power connectors

SATA specifies a different power connector than the four-pin Molex connector used on Parallel ATA (PATA) devices (and earlier small storage devices, going back to ST-506 hard disk drives and even to floppy disk drives that predated the IBM PC). It is a wafer-type connector, like the SATA data connector, but much wider (fifteen pins versus seven) to avoid confusion between the two. Some early SATA drives included the four-pin Molex power connector together with the new fifteen-pin connector, but most SATA drives now have only the latter.

The new SATA power connector contains many more pins for several reasons:[50]

Passive adapters are available that convert a four-pin Molex connector to a SATA power connector, providing the 5 V and 12 V lines available on the Molex connector, but not 3.3 V. There are also four-pin Molex-to-SATA power adapters that include electronics to additionally provide the 3.3 V power supply.[56] However, most drives do not require the 3.3 V power line.[57]

Just like SATA data connectors, SATA power connectors may be straight, upward-angled, or downward-angled.

The power connector is reduced to six pins so it supplies only +5 V (red wire), and not +12 V or +3.3 V.[21][58]

Pin 1 of the slimline power connector, denoting device presence, is shorter than the others to allow hot-swapping.

Note: The data connector used is the same as the non-slimline version.

Low-cost adapters exist to convert from standard SATA to slimline SATA.

SATA 2.6 is the first revision that defined the slimline power connector targeted for smaller form-factors drives, such as laptop optical drives.

The micro SATA connector (sometimes called uSATA or μSATA[59]) originated with SATA 2.6, and is intended for 1.8-inch hard disk drives. There is also a micro data connector, similar in appearance but slightly thinner than the standard data connector.

Some SATA drives, in particular mechanical ones, come with an extra 4 or more pin interface which isn't uniformly standardized but nevertheless serves similar purpose defined by each drive manufacturer. As IDE drives used those extra pins for setting up Master and Slave drives, on SATA drives, those pins are generally used to select different Power modes for use in USB-SATA bridges or enables additional features like Spread Spectrum Clocking, SATA Speed Limit or Factory Mode for Diagnostics and Recovery, by the use of a jumper.[60][61]

Not to be confused with

Standardized in 2004, eSATA (e standing for external) provides a variant of SATA meant for external connectivity. It uses a more robust connector, longer shielded cables, and stricter (but backward-compatible) electrical standards. The protocol and logical signaling (link/transport layers and above) are identical to internal SATA. The differences are:

Aimed at the consumer market, eSATA enters an external storage market served also by the USB and FireWire interfaces. The SATA interface has certain advantages. Most external hard-disk-drive cases with FireWire or USB interfaces use either PATA or SATA drives and "bridges" to translate between the drives' interfaces and the enclosures' external ports; this bridging incurs some inefficiency. Some single disks can transfer 157 MB/s during real use,[17] about four times the maximum transfer rate of USB 2.0 or FireWire 400 (IEEE 1394a) and almost twice as fast as the maximum transfer rate of FireWire 800. The S3200 FireWire 1394b specification reaches around 400 MB/s (3.2 Gbit/s), and USB 3.0 has a nominal speed of 5 Gbit/s. Some low-level drive features, such as S.M.A.R.T., may not operate through some USB[62] or FireWire or USB+FireWire bridges; eSATA does not suffer from these issues provided that the controller manufacturer (and its drivers) presents eSATA drives as ATA devices, rather than as SCSI devices, as has been common with Silicon Image, JMicron, and Nvidia nForce drivers for Windows Vista. In those cases SATA drives do not have low-level features accessible.

The eSATA version of SATA 6G operates at 6.0 Gbit/s (the term "SATA III" is avoided by the SATA-IO organization to prevent confusion with SATA II 3.0 Gbit/s, which was colloquially referred to as "SATA 3G" [bit/s] or "SATA 300" [MB/s] since the 1.5 Gbit/s SATA I and 1.5 Gbit/s SATA II were referred to as both "SATA 1.5G" [bit/s] or "SATA 150" [MB/s]). Therefore, eSATA connections operate with negligible differences between them.[63] Once an interface can transfer data as fast as a drive can handle them, increasing the interface speed does not improve data transfer.

There are some disadvantages, however, to the eSATA interface:

As of August 2017[update] few new computers have dedicated external SATA (eSATA) connectors, with USB3 dominating and USB3 Type C, often with the Thunderbolt alternate mode, starting to replace the earlier USB connectors. Still sometimes present are single ports supporting both USB3 and eSATA.

Desktop computers without a built-in eSATA interface can install an eSATA host bus adapter (HBA); if the motherboard supports SATA, an externally available eSATA connector can be added. Notebook computers with the now rare Cardbus[65] or ExpressCard[66] could add an eSATA HBA. With passive adapters, the maximum cable length is reduced to 1 meter (3.3 ft) due to the absence of compliant eSATA signal-levels.

eSATAp stands for powered eSATA. It is also known as Power over eSATA, Power eSATA, eSATA/USB Combo, or eSATA USB Hybrid Port (EUHP). An eSATAp port combines the four pins of the USB 2.0 (or earlier) port, the seven pins of the eSATA port, and optionally two 12 V power pins.[67] Both SATA traffic and device power are integrated in a single cable, as is the case with USB but not eSATA. The 5 V power is provided through two USB pins, while the 12 V power may optionally be provided. Typically desktop, but not notebook, computers provide 12 V power, so can power devices requiring this voltage, typically 3.5-inch disk and CD/DVD drives, in addition to 5 V devices such as 2.5-inch drives.

Both USB and eSATA devices can be used with an eSATAp port, when plugged in with a USB or eSATA cable, respectively. An eSATA device cannot be powered via an eSATAp cable, but a special cable can make both SATA or eSATA and power connectors available from an eSATAp port.

An eSATAp connector can be built into a computer with internal SATA and USB, by fitting a bracket with connections for internal SATA, USB, and power connectors and an externally accessible eSATAp port. Though eSATAp connectors have been built into several devices, manufacturers do not refer to an official standard.

Mini-SATA (abbreviated as mSATA), which is distinct from the micro connector,[59] was announced by the Serial ATA International Organization on September 21, 2009.[69] Applications include netbooks, laptops and other devices that require a solid-state drive in a small footprint.

The physical dimensions of the mSATA connector are identical to those of the PCI Express Mini Card interface,[70] but the interfaces are electrically incompatible; the data signals (TX±/RX± SATA, PETn0 PETp0 PERn0 PERp0 PCI Express) need a connection to the SATA host controller instead of the PCI Express host controller.

The M.2 specification has superseded both mSATA and mini-PCIe.[71]

Slim 2.5-inch SATA devices, 5 mm (0.20 inches) in height, use the twenty-pin SFF-8784 edge connector to save space. By combining the data signals and power lines into a slim connector that effectively enables direct connection to the device's printed circuit board (PCB) without additional space-consuming connectors, SFF-8784 allows further internal layout compaction for portable devices such as ultrabooks.[72]

Pins 1 to 10 are on the connector's bottom side, while pins 11 to 20 are on the top side.[72]

SATA Express, initially standardized in the SATA 3.2 specification,[73] is an interface that supports either SATA or PCI Express storage devices. The host connector is backward compatible with the standard 3.5-inch SATA data connector, allowing up to two legacy SATA devices to connect.[74] At the same time, the host connector provides up to two PCI Express 3.0 lanes as a pure PCI Express connection to the storage device, allowing bandwidths of up to 2 GB/s.[32][75]

Instead of the otherwise usual approach of doubling the native speed of the SATA interface, PCI Express was selected for achieving data transfer speeds greater than 6 Gbit/s. It was concluded that doubling the native SATA speed would take too much time, too many changes would be required to the SATA standard, and would result in a much greater power consumption when compared to the existing PCI Express bus.[76]

In addition to supporting legacy Advanced Host Controller Interface (AHCI), SATA Express also makes it possible for NVM Express (NVMe) to be used as the logical device interface for connected PCI Express storage devices.[77]

As M.2 form factor, described below, achieved much larger popularity, SATA Express is considered as a failed standard and dedicated ports quickly disappeared from motherboards.

M.2, formerly known as the Next Generation Form Factor (NGFF), is a specification for computer expansion cards and associated connectors. It replaces the mSATA standard, which uses the PCI Express Mini Card physical layout. Having a smaller and more flexible physical specification, together with more advanced features, the M.2 is more suitable for solid-state storage applications in general, especially when used in small devices such as ultrabooks or tablets.[78]

The M.2 standard is designed as a revision and improvement to the mSATA standard, so that larger printed circuit boards (PCBs) can be manufactured. While mSATA took advantage of the existing PCI Express Mini Card form factor and connector, M.2 has been designed to maximize usage of the card space, while minimizing the footprint.[78][79][80]

Supported host controller interfaces and internally provided ports are a superset to those defined by the SATA Express interface. Essentially, the M.2 standard is a small form factor implementation of the SATA Express interface, with the addition of an internal USB 3.0 port.[78]

U.2, formerly known as SFF-8639. Like M.2, it carries a PCI Express electrical signal, however U.2 uses a PCIe 3.0 ×4 link providing a higher bandwidth of 32 Gbit/s in each direction. In order to provide maximum backward compatibility the U.2 connector also supports SATA and multi-path SAS.[81]

SATA uses a point-to-point architecture. The physical connection between a controller and a storage device is not shared among other controllers and storage devices. SATA defines multipliers, which allows a single SATA controller port to drive up to fifteen storage devices. The multiplier performs the function of a hub; the controller and each storage device is connected to the hub.[82] This is conceptually similar to SAS expanders.

Modern[update] PC systems have SATA controllers built into the motherboard, typically featuring two to eight ports. Additional ports can be installed through add-in SATA host adapters (available in variety of bus-interfaces: USB, PCI, PCIe).

Backward and forward compatibility

At the hardware interface level, SATA and PATA (Parallel AT Attachment) devices are completely incompatible: they cannot be interconnected without an adapter.

At the application level, SATA devices can be specified to look and act like PATA devices.[83]

Many motherboards offer a "Legacy Mode" option, which makes SATA drives appear to the OS like PATA drives on a standard controller. This Legacy Mode eases OS installation by not requiring that a specific driver be loaded during setup, but sacrifices support for some (vendor specific) features of SATA. Legacy Mode often if not always disables some of the boards' PATA or SATA ports, since the standard PATA controller interface supports only four drives. (Often, which ports are disabled is configurable.)

The common heritage of the ATA command set has enabled the proliferation of low-cost PATA to SATA bridge chips. Bridge chips were widely used on PATA drives (before the completion of native SATA drives) as well in standalone converters. When attached to a PATA drive, a device-side converter allows the PATA drive to function as a SATA drive. Host-side converters allow a motherboard PATA port to connect to a SATA drive.

The market has produced powered enclosures for both PATA and SATA drives that interface to the PC through USB, Firewire or eSATA, with the restrictions noted above. PCI cards with a SATA connector exist that allow SATA drives to connect to legacy systems without SATA connectors.

Motherboard SATA Ports

Each manufacturer of motherboards, make their SATA ports different. Some motherboards have two ports and others have 4 or more ports. Some motherboards have the primary SATA port as blue and the others brown, but some motherboards will have all of them the same color but they will be labeled starting with 0 and ending with the last of the ports. If the board has two SATA ports, they will be labeled 0 and 1. If they have four ports they will be labeled 0, 1, 2, and 3. The primary drive will be plugged into the blue port (if there is different colors) or SATA 0.

As you can see the connectors have a L shape connection. The plug is also keyed with an L so they can only be plugged in one direction.

For information on SATA cables, click here

For SATA requirements, click here

SATA 3 Gbit/s and SATA 6 Gbit/s

SATA 3 Gbit/s and SATA 6 Gbit/s are compatible with each other. Most devices that are only SATA 3 Gbit/s can connect with devices that are SATA 6 Gbit/s, and vice versa, though SATA 3 Gbit/s devices connect with SATA 6 Gbit/s devices only at the slower 3 Gbit/s speed.